Ransburg HV Controller A12311 Manuel d'utilisateur

SERVICE MANUALLN-9623-00.1March - 2013MODEL: A12311IMPORTANT: Before using this equipment, care-fully read SAFETY PRECAUTIONS, starting on page 1, an

PASSWORD PROTECTIONHigh Voltage Controller parameters will be pass-word protected to prevent an unqualied operator from changing the values.OPERATOR

NOTESFault LEDThe red Fault LED is lit when the system detects a fault condition (see "Figure 3 - Power Switch" in this section). When oper

INSTALLATIONINSTALLATIONFigure 4: InstallationMOUNTINGUsing four (4) each 10" X 32" or M-5 screws (not included), secure the front panel of

Figure 6: Ethernet ConnectorETHERNET CONNECTORUse the appropriate 10/100BASE Ethernet wiring (Straight EIA/TIA 568A) for your installation us-ing a R

OPERATIONMENUS AND OPERATIONOn all of the menus, if there is a parameter that can be changed there are a number of "#" char-acters to show t

Mode MenuFigure 11: Voltage Mode ScreenThis menu displays the current mode (Voltage or Current) and the high and low limits allowed for the Dependen

IP Address MenuFigure 14: IP Address Menu ScreenThis menu allows the setting of the units IP Address. When the new IP Address has been entered, the

CONTROL CONDITIONSPower UpOn power up, the system does several checks to determine hardware status. It checks various sig-nals to determine that ther

ETHERNET IP INPUT BIT DEFINITIONS TABLE 1ETHERNET IP INTERFACEThe Ethernet IP Interface is dened as a set of four 16 bit IO words of input and a set

Input Word 0Bit 0 - Enable Control When this bit is set (high) the system will attempt to keep the actual at the appropriate setpoint.Bit 1 - R

SAFETY:SAFETY PRECAUTIONS...HAZARDS / SAFEGUARDS

ETHERNET IP OUTPUT BIT DEFINITIONS TABLE 2High Voltage Controller - Operation18RansburgLN-9623-00.1

Output Word 0Bit 0 - In Control This bit is set when control is enabled and the control value has closed within three of the setpoint. This doe

Bit 14 - Over Current Fault The current value has exceeded the Current (I) Limit Hi or the Max System Limit.Bit 15 - Cable Fault This bit is se

MAINTENANCETROUBLESHOOTING GUIDEGeneral Problem Procedure SolutionBlank DisplayFaults1. If the display is blank on initial power-up, it may be that

WARRANTY POLICIESLIMITED WARRANTYRansburg will replace or repair without charge any part and/or equipment that falls within the specied time (see bel

Form No. LN-9623-00.1Litho in U.S.A.03/13© 2013 Ransburg. All rights reserved.Models and specications subject to change without notice.Manufacturing

W A R N I N G!W A R N I N G!SAFETYSAFETY PRECAUTIONSBefore operating, maintaining or servicing any Ransburg electrostatic coating system, read and u

Spray AreaAREATells where hazards may occur.HAZARDTells what the hazard is.SAFEGUARDSTells how to avoid the hazard.Fire HazardImproper or inadequate o

AREATells where hazards may occur.HAZARDTells what the hazard is.SAFEGUARDSTells how to avoid the hazard.Spray AreaImproper operation or mainte-nance

AREATells where hazards may occur.HAZARDTells what the hazard is.SAFEGUARDSTells how to avoid the hazard.Spray Area / High Voltage EquipmentElectrical

Toxic SubstancesCertain material may be harmful if inhaled, or if there is contact with the skin.Follow the requirements of the Material Safety Data S

INTRODUCTIONGENERAL DESCRIPTIONThe Ransburg High Voltage Controller (A12311-00 or FRA # EE-4526-300), in conjunction with an appropriate cascade (A122

SPECIFICATIONSOperating Temperature: 0°C to +55°CStorage and ShippingTemperature: -40°C to +85°CHumidity: 95% Non-CondensingPhysical Size: